From: Otto Moerbeek (ottodrijf.net)
Date: Sun Nov 02 2008 - 13:41:45 CST

• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Sun, Nov 02, 2008 at 12:47:16PM -0500, Sean Kennedy wrote:

> Just for Clarity, I did not add rm -rf /usr/obj/* to the list (which I did)
> but all processes I am following are in accordance to FAQ-5 sections 5.3.5
>
> Not like I have been doing this for the past 6 years,
>
> Last time I ran into the Userland Build problem, it was accurately pointed out
> not to miss the [env DESTDIR=/ make-distrib-dirs ] in my userland build.
> OK, I earned that one, unlike then, this appears to be a Missing function call
> in a library, that I missed some obscure and undocumented step to update.
>
> Note: the i386 build was for a system from scratch, using the 4.4 -stable
> install as well as -stable CVS update. I can re-run CVS checkout instead for
> the i386, but then that would mean there is a problem with the src.tar.gz that
> is in the 4.4 -stable release folder on ftp.
>
> Is there a step not listed in FAQ 5.3.5?

No there is not step missing. BUt what you list in your mail is not
what it says.

I suspect you have problems because you run make depend *before* make
obj. Anyway, clean obj; make obj; make build should do the job.

        -Otto
>
> -sean
>
>
> > Date: Sun, 2 Nov 2008 10:14:04 +0100
> > From: ottodrijf.net
> > To: woodentuliphotmail.com
> > CC: techopenbsd.org
> > Subject: Re: -current and -stable 4.4 make build stop in openssl.
> >
> > On Sat, Nov 01, 2008 at 02:04:17PM -0400, Sean Kennedy wrote:
> >
> >> This was an issue I started seeing a week ago, and I thought it a problem
> with
> >> -current but it's in the -stable CVS when a 4.4 stable is installed, the
> >> src.tar.gz is pulled and cvs'ed with -rOPENBSD_4_4 and all good builds
> >> followed. kernel: config GENERIC, make clean, make depend, make, make
> >> install. reboot do userland: make clean, make depend, make obj, 'etc' env
> >> DESTDIR=/ make distrib-dirs, 'src' make build.
> >
> > you not rebuilding userland correctly.
> >
> > -Otto
> >
> >>
> >>
> >> Make build stops on both macppc (-current snapshot 2-days old install) and
> >> i386 4.4-stable install today.
> >> CVS both of them to -rOPENBSD_4_4 and both stop with:
> >>
> >> -(i386)-
> >>
> >> dgst.o(.text+0xf71): In function 'do_fp':
> >> : undefined reference to 'HMAC_CTX_set_flags'
> >> collect2: ld returned 1 exit status
> >> *** error code 1
> >>
> >> -(macppc)-
> >>
> >> dgst.o(.text+0xff4): In function 'do_fp':
> >> : undefined reference to 'HMAC_CTX_set_flags'
> >> *** error code 1
> >>
> >> Both of these are in the /usr/src/usr.sbin/openssl section of the build.
> These
> >> are both brand new installs, and the src tree is built from cvs -stable.
> But I
> >> am loath to admit if the libraries -lssl and -l crypto are completely
> >> up-to-date since one of my tests 3-4 days ago was to update the libraries
> >> manually and re-compile, to no avail.
> >>
> >> I can keep the build stopped here for the moment, (non-production systems,
> >> just test units) and would consider suggestions to look into. (I can test
> on
> >> macppc and then on i386)
> >> This is hardware independent since both show on separate platforms, so if
> a
> >> dmesg is required, I will send, but I did not consider it the factor in
> this
> >> case.
> >>
> >> Sincerely.
> >>
> >> -sean
> >> _________________________________________________________________
>
> _________________________________________________________________

• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]